Hitachi Diagnostic Fault Codes (231)
- 11000-2 — Abnormal EEPROM Faulty MC All Control
- 11001-2 — Abnormal RAM Faulty MC All Control
- 11002-2 — Abnormal A/D Conversion Faulty MC All Control
- 11003-3 — Abnormal Sensor Voltage Faulty MC All Control
- 11004-2 — Abnormal CAN Communication Faulty MC • Heater Control
- 11100-2 — Abnormal Engine Speed Engine Speed: more than 4000 Speed Sensing Control
- 11101-3 — Abnormal Engine Control Dial Voltage: 4.78 V or higher Engine Control Dial Control
- 11101-4 — Abnormal Engine Control Dial Voltage: Less than 0.22 V Engine Control Dial Control
- 11200-3 — Abnormal Pump 1 Delivery Voltage: 4.5 V or higher • HP Mode Control
- 11200-4 — Abnormal Pump 1 Delivery Voltage: Less than 0.25 V • HP Mode Control
- 11202-3 — Abnormal Pump 2 Delivery Voltage: 4.5 V or higher • HP Mode Control
- 11202-4 — Abnormal Pump 2 Delivery Voltage: Less than 0.25 V • HP Mode Control
- 11206-3 — Abnormal Pump 1 Pump Voltage: 4.75 V or higher • E Mode Control
- 11206-4 — Abnormal Pump 1 Pump Voltage: Less than 0.25 V • E Mode Control
- 11208-3 — Abnormal Pump 2 Pump Voltage: 4.75 V or higher • E Mode Control
- 11208-4 — Abnormal Pump 2 Pump Voltage: Less than 0.25 V • E Mode Control
- 11301-3 — Abnormal Swing Pilot Pressure Voltage: 4.75 V or higher • Arm Regenerative Control
- 11301-4 — Abnormal Swing Pilot Pressure Voltage: Less than 0.25 V • Arm Regenerative Control
- 11302-3 — Abnormal Boom Raise Pilot Voltage: 4.75 V or higher • HP Mode Control
- 11302-4 — Abnormal Boom Raise Pilot Voltage: Less than 0.25 V • HP Mode Control
- 11303-3 — Abnormal Arm Roll-In Pilot Voltage: 4.75 V or higher • HP Mode Control
- 11303-4 — Abnormal Arm Roll-In Pilot Voltage: Less than 0.25 V • HP Mode Control
- 11304-3 — Abnormal Travel Pilot Pressure Voltage: 4.75 V or higher • Auto-Idle Control
- 11304-4 — Abnormal Travel Pilot Pressure Voltage: Less than 0.25 V • Auto-Idle Control
- 11307-3 — Abnormal Front Attachment Pi- Voltage: 4.75 V or higher • Auto-Idle Control
- 11307-4 — Abnormal Front Attachment Pi- Voltage: Less than 0.25 V • Auto-Idle Control
- 11400-2 — Abnormal Current Feedback of Current: Both of Higher • Pump 2 Flow Rate Limit Control
- 11400-3 — Abnormal Feedback High Current of Current: Higher than • Pump 2 Flow Rate Limit Control
- 11400-4 — Abnormal Feedback Low Current of Current: Less than 56 • Pump 2 Flow Rate Limit Control
- 11401-2 — Abnormal Current Feedback of Current: Both of Higher • Speed Sensing Control
- 11401-3 — Abnormal Feedback High Current of Current: Higher than • Speed Sensing Control
- 11401-4 — Abnormal Feedback Low Current of Current: Less than 56 • Speed Sensing Control
- 11402-2 — Abnormal Current Feedback of So- Current: Both of Higher Digging Regenerative Control
- 11402-3 — Abnormal Feedback High Current of Current: Higher than Digging Regenerative Control
- 11402-4 — Abnormal Feedback Low Current of Current: Less than 56 Digging Regenerative Control
- 11403-2 — Abnormal Current Feedback of So- Current: Both of Higher Arm Regenerative Control
- 11403-3 — Abnormal Feedback High Current of Current: Higher than Arm Regenerative Control
- 11403-4 — Abnormal Feedback Low Current of Current: Less than 56 Arm Regenerative Control
- 11404-2 — Abnormal Current Feedback of So- Current: Both of Higher • Power Digging Control
- 11404-3 — Abnormal Feedback High Current of Current: Higher than • Power Digging Control
- 11404-4 — Abnormal Feedback Low Current of Current: Less than 56 • Power Digging Control
- 11405-2 — Abnormal Current Feedback of So- Current: Both of Higher Travel Motor Swash Angle Selection
- 11405-3 — Abnormal Feedback High Current of Current: Higher than Travel Motor Swash Angle Selection
- 11405-4 — Abnormal Feedback Low Current of Current: Less than 56 Travel Motor Swash Angle Selection
- 11410-2 — Abnormal Current Feedback of Current: Both of Higher • Pump 1 Flow Rate Limit Control
- 11410-3 — Abnormal Feedback High Current of Current: Higher than • Pump 1 Flow Rate Limit Control
- 11410-4 — Abnormal Feedback Low Current of Current: Less than 56 • Pump 1 Flow Rate Limit Control
- 11910-2 — Actual Engine Speed Faulty Harness • Speed Sensing Control
- 11918-2 — Work Mode Faulty Harness • Attachment Operation Speed In-
- 11911-2 — Security Signal Faulty Harness Theft Prevention Engine Speed,
- 11920-2 — Fuel Flow Rate Faulty Harness Fuel Flow Rate
- 11914-2 — Radiator Coolant Temperature Faulty Harness Radiator Coolant Temperature
- 11901-3 — Hydraulic Oil Temperature Voltage: 4.52 V or higher • Hydraulic Oil Temperature
- 11901-4 — Hydraulic Oil Temperature Voltage: Less than 0.23 V • Hydraulic Oil Temperature
- 11905-3 — Abnormal Boom Bottom Pres- Voltage: 4.5 V or higher • Overload Alarm
- 11905-4 — Abnormal Boom Bottom Pres- Voltage: Less than 0.25 V • Overload Alarm
- 100-3 — Abnormal Engine Oil Pressure Sensor Voltage at the engine oil pressure sensor is below 0.1
- 100-4 — Abnormal Engine Oil Pressure Sensor Voltage at the engine oil pressure sensor is beyond
- 102-3 — Abnormal Boost Pressure Sensor (Ab- Voltage at the boost pressure sensor is below 0.1 V
- 102-4 — Abnormal Boost Pressure Sensor (Ab- Voltage at the boost pressure sensor is beyond 4.9 V.
- 105-3 — Abnormal Boost Temperature Sensor Voltage at the boost temperature sensor is beyond
- 105-4 — Abnormal Boost Temperature Sensor Voltage at the boost temperature sensor is below 0.1
- 108-3 — Abnormal Atmospheric Pressure Sensor Voltage at the atmospheric pressure sensor is below
- 108-4 — Abnormal Atmospheric Pressure Sensor Voltage at the atmospheric pressure sensor is beyond
- 110-0 — Overheating Coolant temperature is beyond 120 °C (248 °F) when
- 110-3 — Abnormal Coolant Temperature Sensor Voltage at the coolant temperature sensor is beyond
- 110-4 — Abnormal Coolant Temperature Sensor Voltage at the coolant temperature sensor is below
- 157-0 — Abnormal common rail pressure (First Common rail pressure is beyond 185 MPa.
- 157-2 — Abnormal common rail pressure When DUTY to the suction control valve is 40 % or
- 157-3 — Abnormal Common Rail Pressure Sensor Voltage at the common rail pressure sensor is beyond
- 157-4 — Abnormal Common Rail Pressure Sensor Voltage at the common rail pressure sensor is below
- P0522 — There is no influence when operating the ma- Nothing special
- P0237 — Dark smoke occurs. Boost pressure cannot be corrected
- P1112 — There is no influence when operating the ma- Nothing special
- P0107 — Dark smoke occurs at high altitude. Atmospheric pressure 80 kPa (0.8 kgf/cm2, 12
- P1173 — There is no influence when operating the ma- Nothing special (The history of overheating is
- P0118 — Normal temperature: When starting, dark smoke When starting: -20 °C (-4 °F) (Start the engine
- P0117 — become loud. When operating: 80 °C (176 °F) (Operate
- P0088 — Vibration of the engine may be large, Rough idle, Prevention the junection system (pump) from
- P0089 — Vibration of the engine may be large, Rough idle, Prevention the junection system (pmp) from
- P0193 — The engine may be stalled. The output power The supply pump can not be controlled
- 172-3 — Abnormal Intake-Air Temperature Sensor Voltage at the intake-air temperature sensor is be-
- 172-4 — Abnormal Intake-Air Temperature Sensor Voltage at the intake-air temperature sensor is below
- 174-3 — Abnormal Fuel Temperature Sensor (Ab- Voltage at the fuel temperature sensor is beyond 4.85
- 174-4 — Abnormal Fuel Temperature Sensor (Ab- Voltage at the fuel temperature sensor is below 0.1 V.
- 190-0 — Overrunning In case the engine speed is beyond 2500 min-1
- 628-2 — Abnormal ROM ROM is broken.
- 633-7 — Pressure limiter open The pressure limiter is open.
- 636-2 — Abnormal Cam Angle Sensor (No Signal) Although the crank signal is present, the cam signal is
- 636-7 — Phase Mismatch of Cam Angle Sensor The right cam pulse is not present at the gap in the
- 639-2 — Abnormal CAN Bus Line Detect the bus line off.
- 639-3 — Abnormal CAN Time Out In case the CAN data reception is not approved in
- 651-3 — Open circuit in injection nozzle #1 drive No input signal of injector 1 monitor.
- 652-3 — Open circuit in injection nozzle #2 drive No input signal of injector 2 monitor.
- 653-3 — Open circuit in injection nozzle #3 drive No input signal of injector 3 monitor.
- 654-3 — Open circuit in injection nozzle #4 drive No input signal of injector 4 monitor.
- 655-3 — Open circuit in injection nozzle #5 drive No input signal of injector 5 monitor.
- 656-3 — Open circuit in injection nozzle #6 drive No input signal of injector 6 monitor.
- P0113 — Nothing special When starting: -10 °C (14 °F) (Start the engine
- P0112 — When operating: 25 °C (77 °F) (Operate nor
- P0183 — Nothing special When starting: -20 °C (-4 °F) (Start the engine
- P0182 — When operating: 70 °C (158 °F) (Operate nor
- P0219 — Engine speed of the excavator may not increase Mistake of gear change, etc
- P0601 — The engine stops. Data of ROM cannot be read
- P1095 — Output power decrease Rial pressure is beyond the allowable pres
- P0340 — • While the engine runs, there is nothing abnor- While the engine runs, operate according to
- P0341 — • After the engine is stalled, the re-start is im- gine stops, the start is impossible (in order to
- P1345 — • While the engine runs, there is nothing abnor- The timing chain and the belt does not turn
- U2104 — Speed is turnd into idle speed. CAN communication is operable
- P0201 — Vibration of the engine is large, Rough idle, out- #1 injector cannot be controlled
- P0202 — rotation speed, output power decrease #2 injector cannot be controlled
- P0203 — #3 injector cannot be controlled
- P0204 — #4 injector cannot be controlled
- P0205 — #5 injector cannot be controlled
- P0206 — #6 injector cannot be controlled
- 723-2 — Abnormal Crank Speed Sensor (No Although the cam signal is present, the crank signal is not
- 987-3 — Abnormal check engine lamp No monitor signal of the check engine lamp
- 1077-2 — Abnormal IC for CPU watching No change of RUN-SUB pulse in 20 msec
- 1079-2 — Abnormal 5 V Power Source 1 When battery volate is between 16 V and 32 V, voltage of
- 1080-2 — Abnormal 5 V Power Source 2 When battery volate is between 16 V and 32 V, voltage of
- 1239-1 — No pressure to pump (Fuel leakage) When pressure to the suction control valve is 900 min-1,
- 1240-1 — No pressure to pump (Fuel leakage) When DUTY to the suction control valve is 33 % or less, or
- 1347-0 — Open circuit in suction control valve The suctioncontrol valve drive current is beyond 2400 mAor
- 1485-2 — Abnormal main relay system Voltage in the main relay system is 1 V or less with the main
- 10001-3 — Abnormal EGR Position (Brushless The condition which the output signal of EGR position cannot
- 10002-2 — Abnormal EGR valve control Difference between the target valve lift and actual position is
- P0335 — • The output power may decrease, white smoke Operate according to standard of the cam sensor
- P0336 — • The engine may be stalled. (If the cam senor is
- P0650 — machine
- P0606 — Output power decrease Sub CPU is broken
- P1631 — Same as Abnormal accelerator Sensor ←
- P1632 — Same as Abnomal atmospheric and in-take ←
- P0087 — Vibration of the engine may be large, Rough idle, Fuel leakage is too much
- P1093 — Vibration of the engine may be large, Rough idle, Fuel leakage is too much
- P0090 — The engine may be stalled and the rotation The supply pump cannot be controlled
- P0487 — There is influence to exhaust gas. As the sensor input is not certain, it cannot be
- P0488 — There is influence to exhaust gas. EGR cannot be controlled
- 10003-2 — Abnormal Injection Nozzle Common ZX160-3 to ZX270-3 class
- 10004-2 — Abnormal Injection Nozzle Common ZX160-3 to ZX270-3 class
- 10005-1 — Abnormal Charge Circuit (Bank 1) In case voltage at bank 1 of charge circuit in ECM is low
- 10006-1 — Abnormal Charge Circuit (Bank 2) In case voltage at bank 2 of charge circuit in ECM is low
- 10007-2 — Abnormal CPU Within 100 msec after the key switch is turned ON, failure of
- 10008-2 — Abnormal A/D Conversion A/D conversion cannot be done.
- 10009-2 — Abnormal 5 V Power Source 3 When battery voltage is between 16 V and 32 V, voltage of
- 10010-2 — Abnormal 5 V Power Source 4 When battery voltage is between 16 V and 32 V, voltage of
- 10011-2 — Abnormal 5 V Power Source 5 When battery voltage is between 16 V and 32 V, voltage of
- 10013-2 — Abnormal EEPROM EEPROM is broken.
- P1261 — Vibration of the engine may be large, Rough idle, The injector cannot be controlled
- P0611 — Vibration of the engine may be large, Rough idle, The injector cannot be controlled
- P1630 — Output power decrease, dark smoke occur. All analogue sensor cannot be used
- P1633 — Same as Abnomal coolant temperature, fuel ←
- P1634 — Same as Abnomal boost pressure and boost ←
- P1635 — Same as Abnomal rail pressure and EGR ←
- P0630 — There is no influence when operating the Data cannot be written to EEPROM
- 14000-2 — Abnormal CAN Communication Data cannot be received due to the noise on the CAN bus
- 14001-2 — ICF: Flash Memory: Read / Write In case the internal memory is abnormal when the key is
- 14002-2 — ICF: External RAM: Read / Write In case the internal memory is abnormal when the key is
- 14003-2 — ICF: EEPROM: Sum Check Error In case the internal memory is abnormal when the key is
- 14006-2 — ICF: Satellite Communication In case communication to the satellite terminal cannot be
- 14008-2 — ICF: Abnormal Internal RAM In case the internal memory is abnormal when the key is
- 14100-2 — Satellite Communication Terminal: Data cannot be received due to the noise on the CAN bus
- 14101-2 — Satellite Communication Terminal: In case the internal memory is abnormal when the key is
- 14102-2 — Satellite Communication Terminal: In case the internal memory is abnormal when the key is
- 14103-2 — Satellite Communication Terminal: In case the internal memory is abnormal when the key is
- 14104-2 — Satellite Communication Terminal: In case communication to the satellite terminal cannot be
- 14105-2 — Satellite Communication Terminal: In case the internal memory is abnormal when the key is
- 14106-2 — Satellite Communication Terminal: In case sending and receiving data are unmatched.
- 13303-2 — Abnormal Thermister Temperature Thermister temperature is 85 °C (185 °F) or higher.
- 13304-2 — Abnormal REG Input H Level During REG input H level
- 13306-2 — Abnormal EEPROM When failure reading EEPROM occurs
- 13308-2 — Abnormal CAN Communication Bus off occurs beyond five times.
- 13310-3 — Shorted circuit in Coolant The state, input 105±30 Ω or less, is kept over 60 seconds.
- 13311-3 — Shorted circuit in Fuel Leverl Sensor The state, input 3±1 Ω or less, is kept over 60 seconds.
- 13311-4 — Open circuit in Fuel Leverl Sensor The state, input 135±20 Ω or less, is kept over 60 seconds.
- 11412-3 — Hyd. Fan P/S Valve FB High Current: Higher than 920 mA • Fan Pump Flow Rate Control
- 11412-4 — Hyd. Fan P/S Valve FB Low Current: Less than 56 mA • Fan Pump Flow Rate Control
- 11802-3 — Boom Bottom Pressure Sensor Voltage: 4.5 V or higher • Overload Alarm Control
- 11802-4 — Boom Bottom Pressure Sensor Voltage: Less than 0.25 V • Overload Alarm Control
- 11976-3 — Auxiliary Valve 2 FB High Current: Higher than 920 mA
- 11976-4 — Auxiliary Valve 2 FB Low Current: Less than 56 mA
- 11977-3 — Auxiliary Valve 1 FB High Current: Higher than 920 mA
- 11977-4 — Auxiliary Valve 1 FB Low Current: Less than 56 mA
- 11980-3 — ATT Relief Change Valve FB Current: Higher than 920 mA
- 11980-4 — ATT Relief Change Valve FB Current: Less than 56 mA
- 11981-3 — Fan Reverse Valve 2 FB High Current: Higher than 920 mA
- 11981-4 — Fan Reverse Valve 2 FB Low Current: Less than 56 mA
- 11982-3 — Fan Reverse Valve 1 FB High Current: Higher than 920 mA
- 11982-4 — Fan Reverse Valve 1 FB Low Current: Less than 56 mA
- 11983-2 — Intake Air Temperature Receive Faulty Harness • Fan Pump Flow Rate Control
- 11984-2 — Boost Temperature Receive Faulty Harness • Fan Pump Flow Rate Control
- 11989-3 — Boom Mode Control Valve FB Current: Higher than 920 mA • Boom Mode Selector Control
- 11989-4 — Boom Mode Control Valve FB Current: Less than 56 mA • Boom Mode Selector Control
- 11991-3 — Selection Control
- 11991-4 — Selection Control
- 11992-3 — Learning
- 11992-4 — Learning
- 11993-3 — Selection Control
- 11993-4 — Selection Control
- 11994-3 — Learning
- 11994-4 — Learning
- 11995-3 — 11995-3
- 11995-4 — 11995-4
- 11997-3 — Bucket Roll-Out Pilot Pressure Voltage: 4.75 V or higher • Boom Mode Selector Control
- 11997-4 — Bucket Roll-Out Pilot Pressure Voltage: Less than 0.25 V • Boom Mode Selector Control
- 11998-3 — Boom Lowering Pilot Pressure Voltage: 4.75 V or higher • Boom Mode Selector Control
- 11998-4 — Boom Lowering Pilot Pressure Voltage: Less than 0.25 V • Boom Mode Selector Control
- 11999-3 — Bucket Roll-In Pilot Pressure Voltage: 4.75 V or higher • Boom Mode Selector Control
- 11999-4 — Bucket Roll-In Pilot Pressure Voltage: Less than 0.25 V • Boom Mode Selector Control
- 20062-0 — Hydraulic Oil Overheat Alarm Hydraulic Oil Temperature: 100 • Overheat Prevention Control
- 91-2 — Accelerator Sensor 1-2 Comparison Fault • Difference in opening angle between accelerator
- P1271 — • 1 system fault: No back-up • 1 system fault: No back-up
- P0523 — • Operationality is not affected. • No back-up
- P0238 — • Black smoke emission • Boost pressure default setting (200 kPa)
- P1113 — • Operationality is affected. • No back-up
- P0108 — • Black smoke emitted at high alti- • Barometric pressure default setting 80 kPa (equivalent
- P0192 — • Engine blow up • Actual rail pressure default setting (80 MPa)
- U2106 — Vary depending on setting Switched to drive control by accelerator sensor input volt
- 1347-4 — PCV1+B Short Circuit PCV1 monitor signal is fixed to High side.
- 1348-0 — PCV2 Open Circuit or Ground Short PCV2 monitor signal is fixed to Low side.
- 1348-4 — PCV2+B Short Circuit PCV2 monitor signal is fixed to High side.
- P1094 — • Intense engine vibration • Limited injection amount 3 (Multi-injection stopped)
- P0091 — • Intense engine vibration • Limited injection amount 3 (Multi-injection stopped)
- P0092 — • Intense engine vibration • PCV1 stop
- P1291 — • Intense engine vibration • Limited injection amount 3 (Multi-injection stopped)
- P1292 — • Intense engine vibration • PCV2 stop
- P1625 — Engine does not start. No back-up
- P1262 — • Intense engine vibration • Common 2 stop (#4, #5, #6 cylinders stopped)
- P0612 — • Intense engine vibration • Common 2 stop (#4, #5, #6 cylinders stopped)
- P0603 — • Operationality is not affected. • No back-up
- 13310-2 — Shorted circuit The state, input 105±30 Ω or less, is Check coolant temperature sensor and
- 13311-2 — Shorted circuit The state, input 3±1 Ω or less, is Check fuel level sensor and harness.